Important information

• Failure to follow the installation instructions included with the display could result in injury and product damage which may not be covered by the warranty.

• Do not open or disassemble the display. You risk electrical shock from the high voltage inside the casing. Opening the casing also voids the warranty.

• Do not stand (or allow children to stand) on a chair to touch the surface of the display. Rather, mount the product at the appropriate height.

• To reduce the risk of fire or electric shock, do not expose the display to rain or moisture.

• If the display requires replacement parts, make sure the service technician uses replacement parts specified by SMART Technologies or parts with the same characteristics as the original.

• Ensure that any cables that cross the floor to the display are properly bundled and marked to avoid a trip hazard.

• Do not insert objects inside the cabinet ventilation holes, because they could touch dangerous voltage points and cause electric shock, fire or product damage which may not be covered by the warranty.

• Do not place heavy objects on the power cable. Damage to the cable could cause shock, fire, or product damage which may not be covered by the warranty.

• Use only extension cords and outlets that can fully accommodate the display’s polarized plug.

• Use the power cable provided with the display. If a power cable is not supplied, contact your supplier. Use only power cables that match the AC voltage of the power outlet and that comply with your country’s safety standards.

• If the glass is broken, do not touch the liquid crystal. To prevent injury, handle glass fragments with care when disposing of them.

• Do not move or mount the display by connecting rope or wire to its handles. The display is heavy, and failure of the rope, wire, or handle could lead to injury.

• Use only VESA-approved mounts.

• Disconnect the display’s power cable from the wall outlet and seek assistance from qualified service personnel if any of the following occur:

  • The power cable or plug is damaged
  • Liquid is spilled into the display
  • Objects fall into the display
  • The display is dropped
  • Structural damage, such as cracking, occurs
  • The display behaves unexpectedly when you follow operating instructions

• Turn off the display before cleaning its screen. Otherwise, you may scramble the desktop icons or inadvertently activate applications when you wipe the screen.

• Avoid setting up and using the display in an area with excessive levels of dust, humidity, and smoke.

• Make sure an electrical socket is near the display and remains easily accessible during use.

• In Europe, the display should be used only with European TN and TT power distribution systems.

  It is not suitable for older, IT-type power distribution systems found in some European countries. “This system (IT-type) is widely used isolated from earth, in some installations in France, with impedance to earth, at 230/400V, and in Norway, with voltage limiter, neutral not distributed, at 230V line-to-line.”

  Contact qualified personnel if you’re uncertain of the type of power system available where you’re installing the display.

• The accessory slot’s maximum available power is 60 W. The slot is not a limited power source. To reduce the risk of fire, make sure that accessories connecting to the slot satisfy the fire enclosure requirements of IEC 60950‑1 and IEC 62368-1.

• You must connect the USB cable that came with the display to a computer that has a USB compliant interface and that bears the USB logo. In addition, the USB source computer must be compliant with IEC 60950-1 and/or IEC 62368-1. It must be certified by UL or CSA or another NRTL / SCC certified body to CSA/UL 60950-1 or CSA/UL 62368-1 and it must have the CE marking. This is for operating safety and to avoid damage to the display.

• Only SMART-provided OPS appliances are supported in SMART Board interactive displays. Third-party OPS appliances are not supported, and their use can lead to poor performance or damage to the display.

• Do not install or remove the OPS appliance while the display is turned on. First make sure the power switch on the back of the display beside the AC power inlet is in the OFF (O) position. If you can’t reach the power switch, use the front control panel’s power button to put the display in Standby mode, and then unplug the display’s power cable from the power outlet.

• After you have turned the display’s power switch off or unplugged it, wait at least 30 seconds before removing the appliance to allow its internal power supplies to discharge completely. You might also wait five minutes to give the appliance the opportunity to cool, if necessary.

• Make sure the OPS appliance is secured to the display with screws through the two anchor points. Inadequately secured appliances can damage the display. (An OPS appliance's anchoring screws are typically captive, although some simply include separate anchoring screws.)

• The following table shows the typical operating power for the display:

  Models	Regulatory Models	Typical power
  6000S (V3)
  SBID-6X65S-V3, SBID-6X65S-V3-PW, SBID-6X65S-V3-P,	IDS665-3	100V to 240V AC, 50 Hz to 60 Hz, 105 W
  SBID-6X75S-V3, SBID-6X75S-V3-PW, SBID-6X75S-V3-P,	IDS675-3	100V to 240V AC, 50 Hz to 60 Hz, 134 W
  SBID-6X86S-V3, SBID-6X86S-V3-PW, SBID-6X86S-V3-P,	IDS686-3	100V to 240V AC, 50 Hz to 60 Hz, 161 W
  6000S (C) and SBID-6000S
  SBID-6X65S-C, SBID-6X65S-CPW SBID-6X65S, SBID-6X65S-PW, SBID-6X65-P	IDS665-1	100V to 240V AC, 50 Hz to 60 Hz, 92W
  SBID-6X75S-C, SBID-6X75S-CPW SBID-6X75S, SBID-6X75S-PW, SBID-6075-P	IDS675-1	100V to 240V AC, 50 Hz to 60 Hz, 141W
  SBID-6X86S-C, SBID-6X86S-CPW SBID-6X85S, SBID-6X85S-PW, SBID-6X86-P	IDS686-1	100V to 240V AC, 50 Hz to 60 Hz, 172W

• For additional requirements and other information, see About your display.

ENERGY STAR is the government-backed symbol for energy efficiency, providing simple, credible, and unbiased information that consumers and businesses rely on to make well-informed decisions. ENERGY STAR-certified products are the simple choice for energy efficiency, making it easy for consumers and businesses to make purchases that save them money and protect the environment. The U.S. EPA ensures that each product that earns the label is independently certified to deliver the quality, performance, and savings that users have come to expect.

As shipped, your display delivers ENERGY STAR performance and savings. However, changing some settings may increase energy consumption beyond the limits required for ENERGY STAR certification. For example, increased brightness and contrast will increase power consumption.

Please consider the environment when you choose non-ENERGY STAR settings.