Raising and lowering your stand
Warning
Ensure the locking bolts are securely tightened before operating the stand.
Do not allow children or people who are not able to safely operate the stand to use it.
To prevent injury, keep hands and people away from crush and pinch locations on the stand.
Operating the stand can create a hand-crushing or hand-pinching hazard. To prevent injury, keep hands and people away from crush and pinch locations on the stand.
Allow adequate clearance above and below the stand to ensure safe raising and lowering.
Caution
Do not raise and lower the stand for more than two minutes at a time.
The stand needs to be calibrated before you start using it.
To calibrate the stand
Connect the stand to a power outlet.
Press the Down button and lower the stand to the lowest position.
Press the Down button for five seconds and then release it.
The stand moves up and down 1 cm.
If the stand lowers but does not move when you try raising it or if you replace the controller, perform a factory reset by following the steps below.
To factory reset the stand
Connect the stand to a power outlet.
Press the Down button and lower the stand to the lowest position.
Press the Down button for five seconds and then release it.
The stand moves up and down 1 cm.
To raise the stand
Press and hold the Up button on the control panel.
Release the Up button to stop raising the display.
To lower the stand
Press and hold the Down button on the control panel.
Release the Down button to stop lowering the display.
The stand’s height-adjustment mechanism locks automatically after 20 seconds of inactivity. Unlock the height-adjustment lock before you raise or lower the stand.
To unlock the stand’s height adjustment
Press the,, and buttons in sequence.
Tip
Don’t allow more than one second between button presses.
The stand needs to be calibrated after you assemble it but before you start to use it.
To calibrate the stand
Connect the stand to a power outlet.
Press the,, and buttons in sequence, and then press down on the control switch for 5 seconds.
Tips
Don’t allow more than one second between button presses.
Calibrating the stand will cause it to move.
The stand moves down 1 cm and then back up.
If the stand lowers but does not move when you try raising it or if you replace the controller, perform a factory reset by following the steps below.
To factory reset the stand
Connect the stand to a power outlet.
Press and hold the and for eight seconds.
The indicator light flashes red three times when the factory reset is complete.
To raise the stand
Lift up and hold the control switch.
The stand rises.
Release the control switch to stop raising the stand.
To lower the stand
Press down and hold the control switch.
The stand lowers.
Release the control switch to stop lowering the stand.
You can set an upper and lower limit for the stand’s height adjustment. If there’s an object that’s blocking the stand’s adjustment path, the height limits prevent the stand from hitting the object.
To set the upper height limit
Raise the stand to the height you want to use as the upper limit.
While pressing and holding the button, lift the control switch up until the indicator light flashes.
Release the button and the control switch.
The upper limit is set.
To set the lower height limit
Lower the stand to the height you want to use as the lower limit.
While pressing and holding the button, press the control switch down until the indicator light flashes.
Release the button and the control switch.
The lower limit is set.
You can save up to two positions in the stand’s memory. You can then raise or lower the stand to these favorite positions.
To set a favorite position
Raise or lower the stand to the height you want to set as the favorite position.
Press the button for two seconds.
The status light flashes white two times. After the stand saves the position, the status light appears solid white.
To raise or lower the stand to a favorite position
Lift up and hold the control switch to raise the stand.
ORPress down and hold the control switch to lower the stand.
The stand rises or lowers until it reaches a favorite position.
Release the control switch within one second.
To raise or lower the stand to a favorite position automatically
Double-tap the control switch from the bottom to raise the stand or from the top to lower it.
The stand rises or lowers until it reaches a favorite position.
Tip
To stop the stand from rising or lowering, tap the control switch once.
To erase all favorite positions from the stand’s memory
Press the button for eight seconds.
The status light flashes red.
Models | |
Keywords |
|
Related documents |