Warnings, cautions and important information for your document camera

• Failure to follow the installation instructions included with the SMART product could result in injury and product damage which may not be covered by the warranty.

• Ensure that any cables that cross the floor to the SMART product are properly bundled and marked to avoid a trip hazard.

• Do not puncture, crush, heat or disassemble the battery, expose it to fire or any liquid, short its terminals, or abuse the battery in any other way as this may cause the battery to explode or ignite, and could cause a fire or injury.

• Don’t install the battery backwards or reverse the polarity. Don’t install other types of battery in the remote control. Both of these actions can cause damage to the remote control and can cause a fire or injury.

• To reduce the risk of fire or electric shock, do not expose the SMART product to rain or moisture.

• Do not push foreign objects into the openings on your SMART product.

• Do not open or disassemble the SMART product. You risk electrical shock from the high voltage inside the casing. Opening the casing also voids your warranty.

• The camera arm on your SMART product has joint that present a pinch hazard when your move the camera arm. Keep clear of the pinch points.

• Do not stare into the light or shine the light directly into someone’s eyes. Turn off the light when capturing images of people.

• Do not overload power outlets or extension cords as this can result in a fire or electric shock.

• Turn off and disconnect your SMART product before a thunderstorm. During a thunderstorm, do not touch your SMART product or the plug, because there is a risk of electrical shock.

• Only use your SMART product with the type or power source that is written on the power supply and do not modify the plug.

• Do not short circuit or allow contract with conductive objects to the battery terminals.

• Do not disassemble batteries.

• Place your SMART product on a solid surface to prevent it from falling.

• If you have a security cable attached to your SMART product, do not carry or swing your SMART product by the security cable.

• Do not connect non-shielded interface cables to your SMART product and do no leave cables connected to unused connectors, because this can cause interference level that exceed FCC regulations.

• Avoid setting up and using the SMART product in an area with excessive levels of dust, humidity and smoke.

• Do not block or cover the opening or slots on your SMART product. These slots provide ventilation, ensure reliable operation and protect your SMART product from overheating.

• Do not carry your SMART product by the camera arm. Carry it by the base of the unit.

• Do not aim the camera lens at the sun.

• If the SMART product requires replacement parts, make sure the service technician uses replacement parts specified by SMART Technologies or parts with the same characteristics as the original.

• Ensure that batteries are stored in a cool and dry place.

• Do not discard batteries in water, fire, or domestic waste. Dispose batteries at collection points.

• Remove the batteries in the remote control if you are not in for an extended period of time. Battery corrosion or leakages can damage the remote control.

• Do not mix new and used batteries.

• Do not mix different types of batteries: alkaline, nickel-cadmium (rechargeable), or carbon-zine.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experience radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator & your body.

FCC

Supplier’s Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Unique Identifier: SDC-650, WD650

Responsible Party – U.S. Contact Information

SMART Technologies (Seattle) Inc.

11100 NE 8th St., Suite 210

Bellevue, WA 98004

compliance@smarttech.com

This device complies with RSS-210 of the Industry Canada Rules. Operating is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:

1. le dispositif ne doit pas produire de brouillage préjudiciable, et

2. ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.

Avertissement:

1. Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les restrictions susmentionnées, notamment :

2. les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur a"n de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;

3. le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.;

4. le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer à la limite de p.i.r.e. spéci"ée pour l’exploitation point à point et non point à point, selon le cas.

5. De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the antenna of this device and all nearby persons.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement non contrôlé.Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

Hereby, SMART Technologies ULC declares that the ratio equipment type Wireless AC Dual Band Adapter, WD650 is an compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: smarttech.com/compliance.

The frequency band and the maximum transmitted power in EU are listed below:

Restrictions in (5GHz)

AT/BE/BG/CZ/DK/EE/FR/DE/IS/IE/IT/EL/ES/CY/LV/LI/LT/LU/HU/MT/NL/NO/PL/PT/RO/SI/SK/TR/FI/SE/CH/UK/HR. 5150MHz-5350MHz is for indoor use only.

SMART Technologies supports global efforts to ensure that electronic equipment is manufactured, sold, and disposed of in a safe and environmentally friendly manner.

Waste Electrical and Electronic Equipment regulations (WEEE and Battery Directive)

Electrical and electronic equipment and batteries contain substances that can be harmful to the environment and to human health. The crossed-out wheeled bin symbol indicates that products should be disposed of in the appropriate recycling stream and not as regular waste.

Batteries

The SMART Document Camera 650 contains rechargeable lithium-ion batteries. The remote contains two AAA batteries. Recycle or dispose of batteries properly.

See smarttech.com/compliance for more information.